Product successfully added to your shopping cart
Quantity
Total
There are 0 items in your cart. There is 1 item in your cart.
Total products
Total shipping  To be determined
Total
Continue shopping Proceed to checkout

1-Wire I2C click

MIKROE-2750

30 g

1-Wire I2C click carries the DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The click runs on a 3.3V power supply.

It communicates with the target microcontroller over 1-Wire® protocol, using the following pins on the mikroBUS™ line: AN, PWM, RST.

More details

$22.00

Quantity Unit Price
5 $20.90
20 $19.80

1-Wire I2C click carries DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The click runs on a 3.3V power supply.

It communicates with the target microcontroller over 1-Wire® protocol, using the following pins on the mikroBUS™ line: AN, PWM, RST.

How the click works

There are two on-board screw terminals used for connecting SCL, SDA, Vcc and GND of the I2C slave. After that, you are able to communicate with that slave through the onboard DS28E17 MCU.

DS28E17 features

The DS28E17 is a 1-Wire slave to I2C master bridge device that interfaces directly to I2C slaves at standard (100kHz max) or fast (400kHz max). Data transfers serially through the 1-Wire® protocol, which requires only a single data lead and a ground return. Every DS28E17 is guaranteed to have a unique 64-bit ROM registration number that serves as a node address in the 1-Wire network.

Specifications

Type 1-wire
Applications 1-Wire I2C click can be used to extend the length of I2C lines by converting I2C to 1-wire
On-board modules DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated
Interface 1-wire,GPIO
Input Voltage 3.3V
Click board size S (28.6 x 25.4 mm)

Pinout diagram

This table shows how the pinout on 1-Wire I2C click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.pngPinNotes
1-Wire 1st pin OW1 1 AN PWM 16 OW2 1-Wire 2nd pin
Reset pin RST 2 RST INT 15 NC
NC 3 CS TX 14 NC
NC 4 SCK RX 13 NC
NC 5 MISO SCL 12 NC
NC 6 MOSI SDA 11 NC
Power supply +3.3V 7 3.3V 5V 10 NC
Ground GND 8 GND GND 9 GND Ground

Programming

Code examples for 1-Wire I2C click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet shows 1-Wire I2C click communication with the Thermo 4 click. It uses skipRom, writeI2C, and readI2C commands to read the temperature data from the sensor, and displays it back via UART output.

01 void One_Wire_I2C_Task()
02 {
03     char uartText [20];
04     char IWireData [20];
05 
06    IWireData [0] = 0x00;   //Thermo 4 temperature register address
07 
08    OWI2C_skipRom ();
09     OWI2C_writeI2C ( OWI2C_WRITE_NORMAL_NOSTOP, 0x48, 1, &IWireData);   //0x48 is unshifted I2C address of Thermo 4 click
10     OWI2C_skipRom ();
11     OWI2C_readI2C ( 0x48, 2, &IWireData);
12 
13    UART_Write (13);
14     UART_Write (10);
15     UART_Write_Text("Current temperature is: ");
16     ByteToStr(IWireData[0], uartText);
17     UART_Write_Text(uartText);
18 
19    Delay_ms (2000);
20 }

Downloads

You Might Also Need

Products in the same category

Send a message

1-Wire I2C click

1-Wire I2C click

What can we do for you?