Product successfully added to your shopping cart
Quantity
Total
There are 0 items in your cart. There is 1 item in your cart.
Total products
Total shipping  To be determined
Total
Continue shopping Proceed to checkout

RELAY click

MIKROE-1370

45 g

RELAY click can control various devices with up to 5A, 250V AC/30V DC loads. It features two G6D1AASI-5DC power PCB relay modules. The click is designed to run on 5V power supply only. RELAY click communicates with the target microcontroller via mikroBUS™ PWM (RL1) and CS (RL2) pins.

More details

$18.00

Quantity Unit Price
5 $17.10
20 $16.20

RELAY click can control various devices with up to 5A, 250V AC/30V DC loads. It features two G6D1AASI-5DC power PCB relay modules. The click is designed to run on 5V power supply only. RELAY click communicates with the target microcontroller via mikroBUS™ PWM (RL1) and CS (RL2) pins.

RELAY click is a compact and easy solution for adding a relay to your design. The two screw terminals onboard allow seamless connectivity.

DO NOT TOUCH THE BOARD WHILE THE EXTERNAL POWER SUPPLY IS ON!

Note: RELAY click has exposed pins/pads. To stay safe take precaution when applying high voltage to the click. The click is to be used by trained personnel only when applying high voltage.

G6D1AASI-5DC power PCB relay

The maximum contact resistance of the G6D1AASI-5DC relay is 100 mΩ.

Communication lines

Communication lines voltage level can be in range between 3.3V and 5V. On-board transistors are used to drive relays by current sinking.

Relay information

A relay is an electrical switch used to terminate or establish a circuit using a low power signal from a microcontroller. It provides complete electrical isolation between microcontroller and controlled circuits. Use the RELAY click™ board with its two G6D1AASI-5DC relays to control various devices with up to 5A, 250V AC/30V DC loads.

Key features

  • On-board screw terminals
  • G6D1AASI-5DC power PCB relay
    • Contact resistance: 100 mΩ max.
    • Max. switching voltage 250 VAC, 30 VDC
    • Max. switching current 5 A
  • Interface: PWM and CS pins
  • 5V power supply

Downloads

Product Type Relay
Applications Board can be used for turning on/off lights, motors and other high power consumers within the maximum supported voltage/current levels
On-board modules G6D1AASI-5DC power PCB relay
Key Features Control up to 5A, 250V AC/30V DC loads
Key Benefits Screw terminals allow seamless connectivity
Interface PWM and CS pins
Power Supply 5V
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)

Pinout diagram

This table shows how the pinout on RELAY click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png
mikroBUStm
Pin Notes
Not connected NC 1 AN PWM 16 PWM RL1
Not connected NC 2 RST INT 15 NC Not connected
RL2 CS 3 CS TX 14 NC Not connected
Not connected NC 4 SCK RX 13 NC Not connected
Not connected NC 5 MISO SCL 12 NC Not connected
Not connected NC 6 MOSI SDA 11 NC Not connected
Not connected NC 7 3.3V 5V 10 +5V Power supply
Ground GND 8 GND GND 9 GND Ground

Programming

Code examples that demonstrate the usage of RELAY click with MikroElektronika hardware, written for mikroC for ARM, AVR, PIC and PIC32 are available on Libstock.

The following code snippet is a simple example of RELAY click toggled with buttons on an EasyPIC v7.

 1 sbit Relay1           at  LATC1_bit;
 2 sbit Relay2           at  LATE0_bit;
 3 sbit Relay1_Direction at TRISC1_bit;
 4 sbit Relay2_Direction at TRISE0_bit;
 5 void main() 
 6 {
 7     Relay1_Direction = 0;                      // Set relay direction as output
 8     Relay2_Direction = 0;                      // Set relay direction as output
 9     Relay1 = 0;                                // Turn off relay1
10     Relay2 = 0;                                // Turn off relay2
11     
12     while( 1 )
13     {
14         if( Button( &PORTB, 0, 80, 1 ) )       // Toggle relay 1 on B0 button press
15             Relay1 = ~Relay1;
16             
17         if( Button( &PORTB, 1, 80, 1 ) )       // Toggle relay 2 on B1 button press
18             Relay2 = ~Realy2;
19     }
20 }

RELAY click is featured in many Libstock projects with different platforms, here is a selection:

You Might Also Need

Products in the same category

Send a message

RELAY click

RELAY click

What can we do for you?