Free shipment for orders above $200 - offer lasts until November 20 at 11:00 CET
Product successfully added to your shopping cart
Quantity
Total
There are 0 items in your cart. There is 1 item in your cart.
Total products
Total shipping  To be determined
Total
Continue shopping Proceed to checkout

DC MOTOR 4 click

MIKROE-2221

DC MOTOR 4 click is capable of driving motors with a supply voltage from 4.5V to 36V. It carries the MAX14870 motor driver from Maxim Integrated.

The click is designed to run on either 3.3V or 5V power supply. DC MOTOR 4 click communicates with the target MCU over the following pins on the mikroBUS™ line: PWM, AN, CS, and INT.

More details

$15.00

Quantity Unit Price
5 $14.25
20 $13.50

DC MOTOR 4 click is capable of driving motors with a supply voltage from 4.5V to 36V. It carries the MAX14870 motor driver from Maxim Integrated. The click is designed to run on either 3.3V or 5V power supply. DC MOTOR 4 click communicates with the target MCU over the following pins on the mikroBUS™ line: PWM, AN, CS, and INT.

The J2 jumper onboard the click is used for selecting a power supply - either the onboard 5V or the external DC motor power supply input.

DC MOTOR 4 click can be used to driving DC motors, controlling the motor's speed, the direction of the rotation, as well to brake and regulate the current.

MAX14870 driver features

The MAX14870 motor driver offers a small, low power solution for driving and controlling brushed DC motors and relays with voltages between 4.5V and 36V.

Very low driver on-resistance reduces power dissipation. It features a charge-pump-less design for reduced external components and low supply current.

How the click works

There are two onboard screw terminals - one is for connecting the DC motor, and the other one is for connecting an external source if necessary. The DC motor is controlled through PWM, CS and AN pin of the click board.


Specifications

Type DC
On-board modules MAX14870 motor driver
Key Features The click is capable of driving motors between 4.5V and 36V
Interface GPIO,PWM
Input Voltage 3.3V or 5V
Click board size M (42.9 x 25.4 mm)

Pinout diagram

This table shows how the pinout on DC MOTOR 4 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

NotesPinMikrobus logo.pngPinNotes
Rotation direction DIR 1 AN PWM 16 PWM

PWM Control Logic Input

NC 2 RST INT 15 FLT

Open-Drain Active-Low Fault Output

Enable IC EN 3 CS TX 14 NC
NC 4 SCK RX 13 NC
NC 5 MISO SCL 12 NC
NC 6 MOSI SDA 11 NC
Power supply +3.3V 7 3.3V 5V 10 +5V Power supply
Ground GND 8 GND GND 9 GND Ground

Buttons and LEDs

DesignatorNameTypeDescription
PWR PWR LED Power LED, lights green when Board is powered.

Jumpers and settings

DesignatorNameDefault PositionDefault OptionDescription
JP1 Data level Left 3V3 Data Level Voltage Selection 3V3/5V, left position 3V3, right position 5V
JP2 Supply selection Power supply selection EXT/5V, right position EXT, left position 5V

Programming

Code examples for DC MOTOR 4 click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet shows the initialization and use of compiler built-in PWM functions to control the motor.

01 void systemInit()
02 {
03     GPIO_Digital_Output(&GPIOA_BASE, _GPIO_PINMASK_4);
04     
05    pwmPeriod = PWM_TIM5_Init(1000);                                   // Set PWM frequency/period (according to the DC motor characteristics)
06     PWM_TIM5_Set_Duty(pwmPeriod,  _PWM_NON_INVERTED, _PWM_CHANNEL1);   // Set current duty for PWM
07     PWM_TIM5_Start(_PWM_CHANNEL1, &_GPIO_MODULE_TIM5_CH1_PA0);          // Start PWM
08 
09 }
10 
11 void main()
12 {
13 
14    systemInit();
15 
16    while (1)
17     {
18         //Forward
19         DIR_PIN = 0;
20         //Forward fast
21         PWM_TIM5_Set_Duty(pwmPeriod,  _PWM_NON_INVERTED, _PWM_CHANNEL1);
22         Delay_ms (3000);
23         //Forward slow
24         PWM_TIM5_Set_Duty(pwmPeriod/2,  _PWM_NON_INVERTED, _PWM_CHANNEL1);
25         Delay_ms (3000);
26         //Reverse
27         DIR_PIN = 1;
28         //Reverse fast
29         PWM_TIM5_Set_Duty(pwmPeriod,  _PWM_NON_INVERTED, _PWM_CHANNEL1);
30         Delay_ms (3000);
31         //Reverse slow
32         PWM_TIM5_Set_Duty(pwmPeriod/2,  _PWM_NON_INVERTED, _PWM_CHANNEL1);
33         Delay_ms (3000);
34 
35    }
36 }

Downloads

You Might Also Need

Products in the same category

Send a message

DC MOTOR 4 click

DC MOTOR 4 click

What can we do for you?