15% OFF on everything in the shop - the offer lasts until June 27, 12:00 CET. Discount applies at checkout
Product successfully added to your shopping cart
Quantity
Total
There are 0 items in your cart. There is 1 item in your cart.
Total products
Total shipping  To be determined
Total
Continue shopping Proceed to checkout

StereoAmp click

MIKROE-2454

25 g

StereoAmp click functions as a stereo amplifier and is ideal for battery operated devices or as a lab amplifier. It features two LM48100Q-Q1 Boomer™ single supply, mono, bridge-tied load amplifier ICs by Texas Instruments. The LM48100Q-Q1 has output fault detection and I2C volume control.

More details

$24.00

Quantity Unit Price
5 $22.80
20 $21.60

The StereoAmp click features a 3.5mm input jack and four output screw terminals for connecting passive speakers. It runs on either 3.3V or 5V power supply and communicates with the MCU through the I2C interface.

stereo-amp-click-page.png

Volume control

Each LM48100Q-Q1 is used for one channel, left or right. Both input paths have their own independent, 32-step volume control.

The mixer, volume control and device mode select are controlled through an I2C compatible interface.

Bridge-tied load for more voltage

Since the output voltage is doubled by connecting the load between the two audio amplifier outputs, the output power is four times stronger then it would be with a single-ended onfiguration.

This is ideal for applications and devices where, due to battery size, the supply voltage is lower.

Shutdown mode

The IC has an I2C selectable low power shutdown mode that disables the device, reducing current consumption to 0.01μA.

Output fault detection

The output fault detection system can sense load conditions and protect the device during short circuit events and detect open circuit conditions. The LM48100Q-Q1 output fault diagnostics are controlled through the I2C interface.

Applications

Automotive audio devices, hands-free kits, battery operated devices, computers, MP3 players, etc.

Key Features

  • Input Voltage Range –0.3 V to VDD = 0.3 V
  • Output Power 1.3 W (at VDD = 5 V, RL = 8 Ω, THD+N ≤ 1%)
  • Low power shut down mode 0.01 μA
  • I2C Volume and Mode Control
  • Input Mixer and Multiplexer
  • Output fault detection
  • Short circuit and thermal protection
  • Individual 32-step volume control
  • 3.5mm input audio jack
  • Screw terminals for speaker output
  • Runs on either 3.3V or 5V power supply

Downloads

Type Audio
Applications Automotive audio devices, hands-free kits, battery operated devices, computers, MP3 players, etc.
On-board modules LM48100Q-Q1 Boomer™ single supply, mono, bridge-tied load amplifier ICs by Texas Instruments
Key Features Screw terminals for speaker output, Individual 32-step volume control
Key Benefits Short circuit and thermal protection, Output fault detection
Interface I2C
Power Supply 3.3V or 5V
Compatibility mikroBUS
Click board size M (42.9 x 25.4 mm)

StereoAmp click functions as a stereo amplifier and features two LM48100Q-Q1 Boomer™ ICs by Texas Instruments. It is ideal for battery powered devices, automotive audio devices, hands-free kits, computers, MP3 players, etc

The LM48100Q-Q1 is a single supply, mono, 1.3W audio power amplifier with output fault detection and I2C volume control.

Features and usage notes

StereoAmp click key features:

  • Input Voltage Range –0.3 V to VDD = 0.3 V
  • Output Power at VDD 1.3 W (at VDD = 5 V, RL = 8 Ω, THD+N ≤ 1%)
  • Low power shut down mode 0.01 μA
  • I2C Volume and Mode Control
  • Input Mixer and Multiplexer
  • Output fault detection
  • Short circuit and thermal protection
  • Individual 32-step volume control
  • I2C interface
  • 3.5mm input audio jack
  • Screw terminals for speaker output
  • Runs on either 3.3V or 5V power supply

Bridge-tied load for more voltage

BTL or a bridge-tied load is an output configuration where the speakers are connected (bridged) between two audio amplifier outputs. In a single-ended configuration one side of the load is connected to the ground. Here both channels are connected, but one has an inverted signal. Compared to a single-ended configuration BTL has two times more voltage swing across the load (speakers).

The doubled voltage swing means four times more power to the speakers. This is ideal for applications and devices where due to battery size the supply voltage is lower.

Pinout diagram

This table shows how the pinout on StereoAmp click corresponds to the pinout on the mikroBUS™ socket.

Notes Pin Mikrobus logo.png
mikroBUStm
Pin Notes
Fault detection left channel FAULT_L 1 AN PWM 16 NC
NC 2 RST INT 15 FAULT_R Fault detection right channel
NC 3 CS TX 14 NC
NC 4 SCK RX 13 NC
NC 5 MISO SCL 12 SCL I2C clock
NC 6 MOSI SDA 11 SDA I2C data
+3.3V power input +3.3V 7 +3.3V +5V 10 +5V +5V power input
Ground GND 8 GND GND 9 GND Ground

Programming

The demo shows how to initialize amplifiers and set volume control registers on the fly. It uses joystick or potentiometer (depending on the development board) to control volume and TFT or LCD display to show gain level. Before initializing I2C module, the demo toggles SDA and SCL lines for proper initialization of amplifiers.

The following code enables amplifiers and selects input 1, sets volume to predefined value, and restores diagnostic register. Function Write_Amp_Reg writes to selected amplifier's register using I2C bus.

 1 void StereoAmp_Init() {
 2     // Power On and Input 1 enabled.
 3     Write_Amp_Reg(LEFT_SPEAKER, MODE_CONTROL_REG, POWER_ON | INPUT1);
 4     Write_Amp_Reg(RIGHT_SPEAKER, MODE_CONTROL_REG, POWER_ON | INPUT1);
 5     // Set volume.
 6     Write_Amp_Reg(LEFT_SPEAKER, VOLUME_CONTROL1_REG, volume_control_L);
 7     Write_Amp_Reg(RIGHT_SPEAKER, VOLUME_CONTROL1_REG, volume_control_R);
 8     // Restore diagnostic.
 9     Write_Amp_Reg(LEFT_SPEAKER, DIAGNOSTIC_CONTROL_REG, DG_RESET );
10     Write_Amp_Reg(RIGHT_SPEAKER, DIAGNOSTIC_CONTROL_REG, DG_RESET );
11 }

You Might Also Need

Products in the same category

Send a message

StereoAmp click

StereoAmp click

What can we do for you?